253MA Stainless Steel | S30815 | 1.4835

Previous 10 / 44 Next

253MA Stainless Steel | S30815 | 1.4835  Stainless Steel 253MA Stainless Steel | S30815 | 1.4835  Stainless Steel


We are the Leading Supplier of 253MA Stainless Steel Plates 
253MA Stainless Steel is a grade combining excellent service properties at high temperatures with ease of fabrication.

We supply and export to Singapore , Indonesia , Brunei and other ASEAN Countries.  
Our specialty is to provide wide range of stainless steel
 with no minimum order (MOQ).

E Steel supply Stainless Steel 253MA Round Bars and Rods , Stainless Steel 253MA Plates and Sheets. 




Stainless Steel 253 MA, UNS S30815, 1.4835, SUS310, SUS310S

253MA Stainless Steel is a grade combining excellent service properties at high temperatures with ease of fabrication. It resists oxidation at temperatures up to 1150°C and can provide superior service to Grade 310 in carbon, nitrogen and sulphur containing atmospheres.

253MA® is a trademark owned by Outokumpu Stainless AB. The standard grade designation covering this grade is UNS S30815. Other mills produce grades compliant with UNS S30815,including Sirius S15®. 253 MA contains a fairly low nickel content, which gives it some advantage in reducing sulphide atmospheres when compared to high nickel alloys and SS310. The inclusion of high chromium, silicon, nitrogen and cerium contents gives the steel good oxide stability, high elevated temperature (creep) strength and excellent resistance to sigma phase precipitation. The austenitic structure gives this grade excellent toughness, even down to cryogenic temperatures.
 

Properties of Sandvik 253MA 

These properties are specified for flat rolled product (plate, sheet and coil) as Grade S30815 in ASTM A240/A240M. Similar but not necessarily identical properties are specified for S30815 in other products such as pipe and bar in their respective specifications, and for Grade 1.4835 in specifications such as EN 10095.

Chemical Composition of 253MA Plate

  C Mn Si P S Cr Ni N Ce
min.  0.05 - 1.10 - - 20.0 10.0 0.14 0.03
max.  0.10 0.80 2.00 0.040 0.030 22.0 12.0 0.20 0.08

 

Mechanical Properties of 253MA Stainless Steel 

Tensile Str (MPa)  Yield Str 0.2% Proof (MPa)  Elongation (% in 50mm)  Hardness
min min min Rockwell B (HR B) max Brinell (HB) max
600 310 40 95 217


 

Corrosion Resistance of S30815, 1.4835 

Although not designed for aqueous corrosion resistance, the high chromium and nitrogen contents give the grade a pitting resistance approximating that of SUS316.  253MA does however have a high carbon content so is highly susceptible to sensitisation; this is likely  to reduce aqueous corrosion resistance after high temperature service or fabrication.  
 

Heat Resistance of 253MA , SUS310 

Oxidation – Excellent resistance to air, at temperatures up to 1100°C.  At high temperatures the steel quickly forms a thin, highly adherent and elastic oxide. This oxide gives good protection even under cyclic conditions, much better than is the case for SUS310. Best resistance is under noncycling conditions.

Carburisation – Under oxidising conditions this grade can perform well, but alloys with higher nickel content are preferred if the atmosphere is reducing.

Sulphidation – good resistance to sulphurbearing gases in an oxidising atmosphere, even if only traces of oxygen are present. Reducing gases prevent the protective oxide forming. 253MA has high strength at elevated temperatures so is often used for structural and pressure-containing applications at temperatures above about 500°C and up to about 900°C. 253 MA will become sensitised in the temperature range of 425-860°C; this is not a problem for high temperature applications, but will result in reduced aqueous corrosion resistance.

 

Heat Treatment of Stainless Steel 253MA 


Solution Treatment (Annealing) -  Heat to 1050-1150°C and cool rapidly. It is recommended that the material be solution treated after 10-20% cold work to achieve maximum creep strength in service. 
This grade cannot be hardened by thermal treatment.

Welding -  Excellent weldability by all standard fusion methods. AS 1554.6 pre-qualifies welding of S30815 with matching Grade 22.12HT rods or electrodes. SUS309 fillers can be used if lower creep strength can be tolerated.
Pure argon shielding gas should be used. 

Machining - As for other austenitic stainless steels, the machining requires sharp tools, slow speeds  and heavy feeds. 
 

Applications of Stainless Steel 253MA 

DIN 1.4835 (253MA Stainless Steel) can be used in the following ways : 

  • Furnace components including burners, retorts, conveyor belts, fans, jigs and baskets, rollers,walking beams, radiant tubes, electric heaterelements, refractory anchors, hoods, flues,grates, expansion bellows. Petrochemical and refinery tube hangers.

Our Sales & Supplier Network

Australia, Pakistan, Malaysia, Taiwan, China, Vietnam, Belgium, Japan, South Korea, Philippines, France, United Kingdom, Indonesia, Thailand, Hong Kong, Sweden, United States, Dubai, Finland, Brunei, Germany & etc.

E Steel is the Global Metal Procurement Company in providing and sourcing raw materials to a variety of engineering industries and sectors. We work as an online B2B Metal Marketplace to help our customers in finding the required steels that are difficult to source locally.


 

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Product Interested  
Quantity  
Email*  
Contact No.*  
Attachment  
*only support gif, jpeg, jpg, png, pdf
Messages*  

Switch to Mobile Version