SUS410 Stainless Steel | SS410 Stainless Steel Plates - Cut To Size Malaysia, Selangor, Kuala Lumpur (KL), Klang Supplier, Suppliers, Supply, Supplies

Standard / System	Country / Region	Grade Designation	Material Number	Notes
AISI / ASTM	USA	AISI 410	UNS S41000	ASTM A240 (plate), A276 (bar)
EN / DIN (Europe)	Europe	X12Cr13	1.4006	EN 10088-2 (plate/strip)
JIS G4304	Japan	SUS410	—	JIS G4304 (hot-rolled plate)
KS D3705	South Korea	STS410	—	Korean standard, JIS equivalent
GB / Chinese Standard	China	1Cr13	—	GB/T 3280 (cold-rolled plate)
BS (UK)	United Kingdom	410S21 / EN56A	—	Older BS 970 designation
ISO 15510	International	X12Cr13	—	ISO harmonised with EN
ASME (pressure vessels)	USA	SA-240 Type 410	UNS S41000	ASME Boiler & Pressure Vessel Code
AMS (aerospace)	USA	AMS 5504	—	Sheet & strip for aerospace
MS ISO (Malaysia)	Malaysia (SIRIM)	X12Cr13	1.4006	Adopts ISO / EN designation

Property	SS410 (UNS S41000 / 1.4006)	SS410S (UNS S41008 / 1.4000)
Carbon content	0.08 – 0.15% max (ASTM A240: 0.08%)	0.08% max (lower carbon)
Hardenability	Fully hardenable by heat treatment	Limited hardening response
Weldability	Requires preheat (min. 205°C) & post-weld temper	Better weldability; less risk of cracking
Corrosion resistance	Moderate; improves in hardened & polished state	Slightly better than SS410 in annealed state
Magnetic?	Yes — all conditions	Yes — all conditions
Primary use case	Hardened components: knives, blades, valve trim, pump shafts	Welded assemblies; structural parts not requiring high hardness
DIN / EN equivalent	1.4006 / X12Cr13	1.4000 / X7Cr14

Grade	C max	Mn max	Si max	P max	S max	Cr	Ni max	Notes
SS410 (A240)	0.08	1.00	0.75	0.040	0.030	11.5 – 13.5	0.75	Plate / sheet
SS410 (A276)	0.15	1.00	1.00	0.040	0.030	11.5 – 13.5	—	Bar / shapes
SS410S (A240)	0.030	1.00	1.00	0.040	0.030	11.5 – 13.5	0.60	Low-C variant
EN 1.4006 (X12Cr13)	0.08–0.15	1.50	1.00	0.040	0.015	11.5 – 13.5	—	EN 10088-2

Grade / Condition	Tensile Strength (MPa) min	Yield Strength 0.2% (MPa) min	Elongation (%) min	HB max	HRB max
SS410 — Annealed (A240)	450	205	20	217	96
SS410 — Hardened (A276, Cond. H)	830	620	12	—	≤43 HRC
SS410 — Tempered (A276, Cond. T)	690	550	15	—	25–31 HRC
SS410S — Annealed (A240)	415	205	22	183	89

Parameter	Details
Thickness	SS410s with maximum thk3mm , SS410 with maximum thk65mm
Origin Mill	Japan Origin (Mill : JFE Steel Corporation) Germany Origin
Mill Test Certificate	Available (3.1 MTC per EN 10204)

Q : What is SS410 used for?

SS410 plate is primarily used in applications requiring a combination of moderate corrosion resistance and high hardness after heat treatment.

Common uses include industrial knife blades, valve seats, pump casings, turbine components, fasteners, and wear-resistant liners.

Q : Is SS410 the same as 1.4006 or X12Cr13?

Yes. SS410, 1.4006, and X12Cr13 all refer to the same martensitic stainless steel grade. SS410 is the American designation (AISI/ASTM), 1.4006 is the European material number (DIN/EN), and X12Cr13 is the European chemical symbol designation per EN 10088. SUS410 (JIS, Japan), STS410 (KS, Korea), and 1Cr13 (GB, China) are also equivalent grades.

Q : Can you cut SS410 plate to custom sizes?

Yes. E Steel provides bandsaw cut-to-size service for SS410 plate. You specify the exact thickness, width, and length required.

There is no minimum order quantity — we can cut a single piece. Most of the plates are ready stock and dispatched from our Klang warehouse.

Q : What is the difference between a full plate and cut-to-size plate?

A full plate is the standard mill plate size as-produced — typically 1,219 mm×2,440 mm, 1,500 mm×3,000 mm, or similar standard sheet sizes.

Cut-to-size (also called cut-to-length) means the plate has been sawn to your specified dimensions, saving material waste and machining time at your facility.

E Steel can supply either — full plate for customers who will cut in-house, or cut-to-size for customers who need ready blanks.

Q : Is SS410 magnetic?

Yes, SS410 is magnetic in all conditions — both in the annealed (soft) condition and in the hardened-and-tempered (hard) condition.

This distinguishes it from SS304 and SS316, which are generally non-magnetic. SS410's magnetism is relevant for applications such as magnetic chucks in machining, magnetic separation equipment, and motor or sensor components where ferromagnetic properties are required.

Q : Can SS410 rust?

SS410 can develop light surface rust if exposed to moist atmospheric conditions or chloride-containing environments for prolonged periods.

It is significantly less corrosion-resistant than SS304 or SS316 because of its lower chromium content (~12% vs. ~18%).

For outdoor applications in tropical Malaysia, Singapore, or coastal Indonesia, a surface finish (polished or coated) is recommended, and the application should be reviewed against SS316L if chloride exposure is anticipated.

Q : Do you supply SS410 with a Mill Test Report (MTR)?

Yes. Material Test Reports to EN 10204 3.1 are available for all SS410 / SS410s stainless steel plate supply.

Heat number traceability is maintained through the cutting process, so cut pieces retain their MTR linkage.

Q : What sizes of SS410 plate are available in Malaysia?

E Steel stocks SS410 plate from 3 mm to 65 mm thickness.

Thicker sections (above thk65mm) are available on request through our procurement network.

Cut-to-size service is available for any dimension within the stocked plate footprint. Contact our sales team for current stock availability and lead times.